Microcement in Palm Beach for Floors, Walls and Showers
Across Palm Beach County, a lot of renovation requests start the same way: dated marble or ceramic tile in a bathroom, kitchen or stair, and an owner who wants a calm, continuous surface without jackhammers or weeks of noise. Microcement flooring does that. It bonds over sound existing tile and concrete at a few millimeters thick, wraps floors, walls and shower enclosures in one seamless finish, and is troweled by hand, so every room has slight natural movement in tone. We install it on Palm Beach Island, in West Palm Beach condos and in homes from Jupiter to Tequesta.
The Short Answer
Microcement in Palm Beach is a hand-troweled cementitious finish applied in thin layers over existing tile, concrete or board, creating seamless floors, walls, showers and stairs without demolition. Art of Coating Miami quotes it after an on-site assessment; installed cost commonly sits in a higher range than resin floor coatings because of the hand labor and surface prep involved. Most rooms take several working days plus cure time. In coastal humidity it lasts when substrates are moisture-tested, showers are waterproofed first and the finish is properly sealed.
Reviewed October 14, 2026 by the Art of Coating Miami installation team.
Palm Beach Homes and Spaces Suited to Microcement
The properties we see vary from oceanfront estates on Palm Beach Island to high-rise condos along Flagler Drive in West Palm Beach and single-family homes in Jupiter, Tequesta and North Palm Beach. Microcement works in most of them. Primary bathrooms are the most common request: floor, shower walls, bench and niche finished as one surface with no grout lines. Kitchens use it on floors and backsplashes. Stair treads and risers can be wrapped to match the floor below. Powder rooms, walk-in closets, living areas and covered loggias round out the list. Because it adds so little height, it fits condos where door clearances and threshold transitions to adjoining rooms would not allow a new layer of tile, and it avoids the demolition that many buildings restrict.
Substrates, Humidity and Salt Air in Palm Beach
Microcement is only as good as what it sits on. Existing tile has to be tightly bonded; hollow-sounding or cracked tiles are removed and patched before anything else. Ground-floor slabs in Palm Beach County sit over a high water table, so we test concrete with ASTM F2170 relative humidity probes or ASTM F1869 calcium chloride kits before priming, and adjust the system when readings are high. Coastal humidity slows drying between coats, which is why we schedule layers by conditions rather than by the clock and keep air conditioning running during the job. Salt air on Palm Beach Island and Jupiter Island matters most on covered outdoor areas, where the sealer choice and maintenance plan carry more weight. Showers always get a waterproofing membrane under the microcement; the finish itself is not the waterproofing.
Recommended Microcement Systems and Finishes for Palm Beach
A typical system is a primer matched to the substrate, a fiberglass mesh embedded in the first base coat over tile to bridge grout lines, one or two base coats, two finish coats, then a penetrating sealer and a protective polyurethane or polyaspartic-type topcoat. Interior floors and walls use finer finish grades for a soft, smooth look; shower floors, stairs and outdoor covered areas use a coarser grade or added texture for grip. Color is mixed on site from a palette that leans toward warm whites, sands, greiges and stone grays, which suit Palm Beach interiors well. Sheen ranges from matte to satin. For the interior side of the house, our home interior flooring page covers how microcement compares with resin and polished options room by room.
How We Install Microcement in Palm Beach Homes
Work begins with a free on-site assessment: we tap-test tile, check for cracks and movement, take moisture readings on slabs, measure door and threshold clearances and confirm finish samples. A written itemized estimate follows. On install, the room is masked and furniture protected, tile is cleaned and degreased, loose pieces are reset or removed, and cracks are repaired. Showers receive a waterproofing membrane. Primer goes down, then mesh embedded in the first base coat. Each base and finish coat is hand-troweled, allowed to dry, and lightly sanded between passes. Sealer and topcoat are applied last, following the manufacturer's technical data sheet for coat counts and recoat windows. Because nothing is demolished, there is no jackhammering and very little debris, which matters in condo towers and occupied estate homes.
Microcement Cost in Palm Beach
Microcement is quoted after an on-site assessment rather than from a fixed per-foot price. Installed cost commonly falls in a higher range than resin floor coatings, because every layer is applied and finished by hand and the prep over tile is detailed work. Variables that move the price include the substrate and how much tile needs resetting, whether walls and showers are included, the number of corners, niches, benches and stair edges, waterproofing requirements, finish grade and color, and building logistics such as elevator booking and work-hour limits. A single open floor is more efficient per foot than a shower with niches and a bench. When you compare quotes, compare the full system: tile prep, mesh, base and finish coats, sealer and topcoat. Our microcement cost and pros and cons guide explains the trade-offs in more detail.
Palm Beach Microcement Timeline and How to Prepare
A typical bathroom follows this rhythm. Day one: protection, tile cleaning, repairs and waterproofing in the shower. Day two: primer, mesh and first base coat. Day three: second base coat and sanding. Day four: finish coats. Day five: sealer and topcoat. Larger or multi-room jobs add days, and humid weather can stretch drying between coats. Light foot traffic is usually fine once the topcoat has dried; furniture, rugs and shower use wait for the cure time on the data sheet. To prepare, clear the rooms, remove toiletries and loose fixtures you want to keep, and plan another bathroom for the week. Condo owners should reserve the service elevator and confirm work hours with management. Afterward, clean with pH-neutral soap and avoid acidic or abrasive cleaners that can dull the sealer.
When Microcement Fits in Palm Beach Homes
Microcement fits when you want a seamless, minimal look across floors and walls, when tile is sound and demolition is impractical, and when low added height matters. It is a strong choice for bathrooms, showers, kitchens, stairs and covered living areas. Other systems fit better in some cases. Garages need epoxy or polyaspartic built for hot tires and chemicals. Uncovered pool decks in full sun do better with a purpose-built pool deck coating. Large open slabs where budget matters may be better served by concrete floor polishing. Tile that is loose across a whole floor needs removal first, which changes the economics, and areas with active slab cracking need structural repair before any thin finish goes down. Concrete Network offers useful independent background on overlays before you decide.
Palm Beach and Jupiter Areas We Serve
We install microcement on Palm Beach Island from the estate section through the north end, across West Palm Beach condos and townhomes along Flagler Drive and downtown, and in Jupiter, Jupiter Island, Tequesta, Juno Beach, North Palm Beach and Palm Beach Gardens. To the south, our crews also work in Lake Worth Beach, Manalapan and Boca Raton, and inland toward Wellington. Homeowners in the north county are covered by the same crews and the same assessment process. Many projects come through designers and builders renovating existing homes, and we coordinate with them on finish samples, sequencing with plumbing and cabinet trades, and the punch list. Whether it is a single powder room or a full home, the assessment and estimate process is the same.
Why Palm Beach Owners Choose Art of Coating Miami
Microcement is unforgiving of shortcuts, so owners look for an installer who preps carefully and explains the system. We are licensed and insured, working since 2022 across Miami-Dade, Broward and Palm Beach counties with more than 500 projects completed, a BBB A+ rating and a 5.0 Google rating. We test before we coat, waterproof showers before finishing them, and follow the manufacturer's technical data sheets for every layer. You get finish samples to approve, a written itemized estimate and a written warranty. Our crews protect finished rooms, keep dust low, coordinate with building management and leave condo hallways and elevators clean. Call (786) 618-4877 to schedule a free on-site assessment of your Palm Beach, West Palm Beach or Jupiter home.
Palm Beach Floor Coating FAQs
How much does microcement cost in Palm Beach?+
Can microcement go over existing tile?+
Is microcement waterproof in a shower?+
How long does a microcement bathroom take?+
Can microcement be used outside in Palm Beach?+
Related Services & Coverage
Serving Palm Beach & Palm Beach County
Art of Coating Miami is a licensed, insured, BBB A+ contractor serving Palm Beach and the surrounding Palm Beach County area with free on-site estimates.
How We Do the Work: Methods & Standards
- Moisture testing before any coating goes down — calcium chloride (ASTM F1869) or in-slab relative humidity (ASTM F2170) — with vapor-mitigating primer when readings call for it. (ASTM International)
- Mechanical surface preparation by diamond grinding to the concrete surface profile (CSP) the coating system specifies, with cracks, joints and spalls repaired first. (ICRI)
- Mix ratios, film thickness, recoat windows and cure times taken from the manufacturer’s technical data sheet for the exact system installed.
- Slip-resistant texture specified for wet areas, ramps and pool surrounds; workplace floors planned around OSHA walking-working surface requirements. (OSHA)
- A written, itemized estimate after a free on-site assessment, and a written warranty on completed work.
Get Your Free Palm Beach Estimate
Licensed, insured & trusted across Palm Beach County. We reply within 24 hours.